How To Hack WI-FI WEP With Back|Track 5

What you need for this crack are a few simple things, a copy of backtrack 5 booting off a DVD or a flash drive and a compatible wireless card that supports packet injection. Now if you can't get to this screen, and you are stuck at the terminal you get when booting into backtrack, you need to type startx and wait a couple of minutes for the desktop to show. Okay so let's begin, so first we need to open a terminal. To do that, just click the little icon that's on the right side from System. Please see the image below:



Now type airmon-ng and that command displays our interfaces. In my case I have wlan0, and now we are going to put it into monitor mode. To do that, type airmon-ng start wlan0. As you can see on the picture below it says (monitor mode enabled on mon0), and we are going to be using mon0 instead of wlan0 as our interface.




Type airodump-ng mon0 and that will start scanning for wi-fi networks. As you can see, there is a network called SKIDHACKER. Take a note of the BSSID the DATA, the CHANNEL and the type of ENCRYPTION. Please refer to the image below, if you have any trouble getting to that point.




Now we are going to set it to lock on a specific network named SKIDHACKER. To do that, type airodump-ng -c (channel) -w WEPcrack --bssid (bssid of the network) mon0. Replace (channel) with the channel of the network you are trying to crack, and replace (bssid of the network) with the bssid of the network you want to crack.




Okay so as you can probably see the data is going really slow, and we need to boost that up. We are going to need a lot more data, so let's preform one of the aireplay commands that will boost that data. Firstly, open up a new terminal and type aireplay-ng -1 0 -a (bsisd) mon0 where (bssid) is the bssid of the network. Now if your wi-fi card is supported, you should see Association successful :-), if you don't see that then your card is not supported.




Now we are going to type in aireplay-ng -2 -p 0841 -c FF:FF:FF:FF:FF:FF -b (bssid) mon0. And now when the question Use this packet ? pops up, just push the letter y. And now as you can see in the image below, the data went high drastically.




Okay so now lets open a new terminal and we are going to attempt to crack it with the amount of data we have. I recommend getting over 20000 data before trying to crack it. So let's type aircrack-ng WEPcrack*.cap. Replace WEPcrack with the filename you chose before when capturing the data, and don't forget to add that asterisk after the file and the extension which is .cap.




And now it will attempt to crack the password. Just wait a couple of minutes for it to complete, and once it did it will say KEY FOUND! [ XX:XX:XX:XX:XX ] where the X's will be random numbers and/or letters. That's not it, now to connect you will need to remove the semicolumns. For an example, if we were to have 12:34:52:66:59, the password would be 1232526659. Just log in to your Windows OS, and connect using that password.

So lets begin. What you will need for this crack is a dictionary file that we are going to use to crack the WPA/WPA2 password. Remember, the bigger the dictionary file is the greater the chance you have in cracking the password. So now you are probably wondering, where do I get a dictionary file? Well, I don't know if this is allowed or not but I recently downloaded a 1.9GB dictionary file.

To get the file please PM me, I can't risk getting this tutorial taken down. Okay, so firstly open up a terminal and once we have the terminal open we are going to type in airmon-ng which will display our wireless interfaces. In my case I have wlan0, and now we are going to put it into monitor mode. To do that, type airmon-ng start wlan0. As you can see on the picture below it says (monitor mode enabled on mon0), and we are going to be using mon0 instead of wlan0 as our interface.


Lets type in airodump-ng mon0 and this command is going to initiate the scanning process for Wi-Fi networks. As you can see in the picture below, a few WPA encrypted networks should pop up. I'm going to attempt to crack the network under the essid SKIDHАCKER. Take a note of the channel, and you want to copy the BSSID for later use.



Now we are going to type in airodump-ng -c (channel) -w (filename) --bssid (bssid) mon0, and replace the values to fit what you got from the last step. Don't forget to remember what filename you chose, because we are going to need that at the end.



What is needed to crack a WPA or WPA2 key is something called a WPA Handshake. You can obtain a handshake by kicking someone off the network, and those computers will automatically reconnect which will give you the handshake. This means, if there is no one on the network, you can't get a handshake, and you can't crack the WPA network. So how do we know if someone is connected? Well look at the lower part of the airodump command, and you will notice something as STATION, and underneath that if someone is connected it wil show you their mac address.



Once you get a handshake, airodump will alert you in the top screen, and the handshake will be located right from the time stamp. Okay, so lets open up a new terminal and we are going to kick off the computers connected. Lets type in aireplay-ng -1 0 -a (bssid) mon0. replace bssid with the network you are trying to crack and hit enter. It is going to attempt to kick off a client, and if it succeeds you will see the wpa handshake at the top right corner, if you don't run the aireplay command a couple of times.



So now that we have a wpa handshake file, we are going to attempt to crack it. Lets stop the scan by pressing CONTROL + C on the terminal where airodump is running. Now in order to find the handshake file, you need to go in the top menu and chose Places > Home Folder. Okay, so lets open up a terminal and we are going to type in aircrack-ng -w (dictionary) /root/(filename). Where filename is the filename you specified when capturing the wpa handshake and the dictionary is the path of the wordlist you downloaded. This can be done by dragging in the handshake file into the terminal after the aircrack-ng -w (dictionary) command and it will parse in it's directory. All you need to do is hit enter. The password needs to be in the dictionary file, so the bigger the wordlist is the bigger are the chances of you getting the password.



If the password is in the wordlist, it will give you a success message and the key in brackets. Happy hacking, hackers!

---

•